Danh mục sản phẩm


Danh mục sản phẩm > > Tecsis Sensor > EZE30


Mã sản phẩm: EZE30
Nhà Sản Xuất:

Tecsis Sensor

Tài liệu hướng dẫn Download


Digital amplifiers are used to adjust the mV/V-output signal of strain gauges to a connected control. The model EZE30 comes with an integrated LED-display which allows also to display the measured data immediately. Controllers can be connected through the many interfaces. The amplifier has 3 relay outputs, one analogue output, one serial RS-422/485 interface and 3 logical inputs.

 The model EZE30 series is designed for lightly dynamic and static applications for example weighing. The user-friendly device for top hat rail mounting comes with big screw-type terminals, a LED-display and keys which can be used to operate the amplifier or to set its parameters.


  • Amplifier for strain gauges with LED-Display mountable on top hat rails
  • Can be configured via keyboard or PC
  • Digital output signal via serial RS-422/RS-485 interface
  • Freely programmable analogue output (2-20 mA)
  • 3 freely programmable limit contacts
  • 3 logical inputs for remote controll
  • Limit frequency up to 20 Hz for quasi static applications
  • Accuracy 0,002 % of full scale
  • Up to 4 strain gauges with 350 ohm parallel connectable
  • Supports 6-wire technology
  • Bridge supply 5 VDC
  • Needed power supply 12-24 VDC
  • User friendly and easy to maintain because of big screw-type terminals, keys and LED-Display
  • Easy communication via big set of ASCII-commands
  • Protection class IP 40

Because of its high accuracy and speed of the A/D converter the amplifier EZE30  suits especially well for weighing but also can be used to measure and monitor forces at engines. Measured data and the status of the in- and outputs are displayed on the 5 digit digital display. It is possible to connect all kinds of strain gauges (max 4 sensors, 350 ohm) with an output signal up to ± 3,2 mV/V. The internal sensor supply is 5 VDC. The internal sensor supply is 5 VDC. Usually the amplifier is not pre-adjusted and the customer connects it to the force transducer and also adjusts it. The amplifier can be programmed either by keyboard or by ASCII-commands via pc. A menu guides the programming. The keys also allow to tare and to set a new zero-point. Through a standard terminal programm it is possible to communicate via the seriel RS-485 interface. A software with oscilloscope function which runs under windows is also available. The 3 relays can be used to monitor if limit values are underran or overtraveled. The analog output, which can also be programmed freely offers a 2-20 mA output signal for analog processing. The many possiblities to adjust filters allow to damp interfering signals.

» Tecsis Sensor - P1440/P1442/P1444/P1446/P1495: 0 VND (P1440/P1442/P1444/P1446/P1495)
» Tecsis Sensor - E1930: 0 VND (E1930)
» Tecsis Sensor - E1931: 0 VND (E1931)
» Tecsis Sensor - E1931X402: 0 VND (E1931X402)
» Tecsis Sensor - E1930X800: 0 VND (E1930X800)
» Tecsis Sensor - E1932: 0 VND (E1932)
» Tecsis Sensor - E1999: 0 VND (E1999)
Liên Hệ Trực Tuyến

Tel: (08) - 3511.5746

Fax: (08) - 3511.7931

Hot Line: 0978.996.122


belimo dwyer fireye spirax-sarco


Cảm Biến - Sensor

Lượt truy cập

29-31 Dinh Bo Linh Street, Ward 24, Binh Thanh District.
Telephone: 08-3511.5746      Fax: 08-3511.7931
Email: kd2@cntruongthanh.com
Hotline: 0978.996.122
Copyright © 2010 cntruongthanh.com
Phát triển bởi N N H